// Sys Lib
#include <stdio.h>
#include <string.h>
#include <stdlib.h>
// My Lib
#include <My_Arduino_GPIO_Lib_V1_8.h>
//#include <My_Arduino_FND_Lib_V2_7.h>
// PRJ Lib
#define GPIO_IF 1
#define Digit_4 2
//#define Fnd_Dis 3
#define Fnd_Led_Dis 4
//#define En_Font_Dis 5
#include "fnd_dis.h"
uint16_t cnt16 = 1234;
uint16_t t_loop = 0;
uint16_t buf;
uint8_t led_cnt=0;
char d_buf[50];
#define Arduino_Mode 1
#define HW_Uart_mode 2
extern int out_dev_set_mode;
#include <My_MCU_Printf_Lib_V2_6.h>
struct TIME
{
int tm_loop;
char sec;
char min;
char hour;
}time = {0, 0, 17, 15};
struct TIME *tm = &time;
void setup() {
int hj = 0;
// put your setup code here, to run once:
//DDRD = DDRB = 0xff;
for(int i = 0; i<= 7;)
{ // LED + FND DIR Set
pinMode(LED_pin[i], OUTPUT);
Led_Byte_Out(0xff); // init
i++;
}
pinMode(x1000, OUTPUT);
pinMode(x100, OUTPUT);
pinMode(x10, OUTPUT);
pinMode(x1, OUTPUT);
#if Fnd_Led_Dis
pinMode(led_scan_pin, OUTPUT);
#endif
Serial.begin(115200);
out_dev_set_mode = HW_Uart_IF_Mode;
Flag_sts.Dp_X100_Flag = 1;
}
void loop() {
// put your main code here, to run repeatedly:
_delay_ms(1);
tm -> tm_loop++;
if(tm ->tm_loop > 990) // 1sec chk sum
{// if-1
tm -> tm_loop = 0;
tm -> sec++;
if((*tm).sec > 59) // 1 min chk sum
{ //if-2
tm -> sec = 0;
time.min++;
if(tm -> min > 59) // 1 Hour Chk sum
{ // if-3
(*tm).min = 0;
tm -> hour++;
if((*tm).hour > 23) time.hour = 0;
} //if-3-end
} // if-2-end
Flag_sts.Dp_X1_Flag = !Flag_sts.Dp_X1_Flag;
// printf
dev_printf("Now Time = %d : %d : %d\r\n", (*tm).hour, time.min, tm ->sec);
} // if-1-end
/*
t_loop++;
if(t_loop > 200)
{
t_loop = 0;
(cnt16 > 2000) ? cnt16 = 1234 : cnt16++;
if(cnt16 % 20 == 0) led_cnt++;//buf = cnt16;
Flag_sts.Dp_X1_Flag = !Flag_sts.Dp_X1_Flag;
//Serial.print("Now Cnt = ");
//Serial.println(cnt16); // hi
//Hi
dev_printf("Now Cnt= %d\r\n", cnt16);
// mid
// sprintf(d_buf,"Now Cnt= %4d\r\n", cnt16);
// Serial.print(d_buf);
// Low
// Serial.write(cnt16 /1000 + 0x30);
// Serial.write(cnt16 %1000/100 + '0');
// Serial.write(cnt16 %100/10 + 48);
// Serial.write(cnt16 %10 + 0x30);
// Serial.println("");
}
*/
#if En_Font_Dis
fnd_dis_en_font(H,E,L,P);
#elif Fnd_Led_Dis
fnd_led_dis(tm -> min * 100 + tm ->sec, tm -> sec);//map(cnt16, 1234, 2000, 0, 255));
#elif Fnd_Dis
fnd_dis(cnt16);
#endif
}